« Back
Home /
CLIA Kit for Pigment Epithelium Derived Factor (PEDF)

CLIA Kit for Pigment Epithelium Derived Factor (PEDF)

Item no.	SCB972Mu-24T
Manufacturer	Cloud-Clone
Amount	24T
Category	ELISA & Immunoassays Immunoassay CLIA Kits CLIA
Type	Clia
Specific against	Mouse
ECLASS 10.1	32161000
ECLASS 11.0	32161000
UNSPSC	41116126
Alias	SERPINF1; EPC1; PIG35; SDF3; Serpin F1; Cell proliferation-inducing gene 35; Serpin Peptidase Inhibitor,Clade F Member 1(Alpha-2 Antiplasmin); Stromal Cell Derived Factor 3
Available
Quantity options
Detection range	0.14-100ng/mL
Organism species	Mus musculus (Mouse)
Sensitivity	The minimum detectable dose of this kit is typically less than 0.05ng/mL
Sample type	Serum, plasma, tissue homogenates, cell lysates, cell culture supernates and other biological fluids
Assay length	2h, 40min
Method	Double-antibody Sandwich
Specificity	This assay has high sensitivity and excellent specificity for detection of Pigment Epithelium Derived Factor (PEDF). No significant cross-reactivity or interference between Pigment Epithelium Derived Factor (PEDF) and analogues was observed.
Precision	Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Pigment Epithelium Derived Factor (PEDF) were tested 20 times on one plate, respectively. Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Pigment Epithelium Derived Factor (PEDF) were tested on 3 different plates, 8 replicates in each plate. CV(%) = SD/meanX100 Intra-Assay: CV<10% Inter-Assay: CV<12%
Stability	The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition. To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Assay procedure summary	1. Prepare all reagents, samples and standards; 2. Add 100µ L standard or sample to each well. Incubate 2 hours at 37° C; 3. Aspirate and add 100µ L prepared Detection Reagent A. Incubate 1 hour at 37° C; 4. Aspirate and wash 3 times; 5. Add 100µ L prepared Detection Reagent B. Incubate 30 minutes at 37° C; 6. Aspirate and wash 5 times; 7. Add 100µ L Substrate Solution. Incubate 10 minutes at 37° C; 8. Read RLU value immediately.
Test principle	The microplate provided in this kit has been pre-coated with an antibody specific to Pigment Epithelium Derived Factor (PEDF). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Pigment Epithelium Derived Factor (PEDF). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Pigment Epithelium Derived Factor (PEDF) level in the sample or standard.;
Research Area	Cytokine; Neuro science;

Note: The presented information and documents (Manual, Product Datasheet, Safety Datasheet and Certificate of Analysis) correspond to our latest update and should serve for orientational purpose only. We do not guarantee the topicality. We would kindly ask you to make a request for specific requirements, if necessary.

All products are intended for research use only (RUO). Not for human, veterinary or therapeutic use.